- 您现在的位置：买卖IC网 > Sheet目录470 > MAX11008EVC16 (Maxim Integrated)EVAL KIT MAX11008
Dual RF LDMOS Bias Controller with
Nonvolatile Memory
MAX11008 returns to F/S mode. Use a repeated START
condition in place of a STOP condition to leave the bus
active and the mode unchanged. Figure 9 summarizes
the data bit transfer format for HS-mode communication.
Register Address/Data Bytes (Write Cycle)
A write cycle begins with the bus master issuing a
START condition followed by 7 address bits (see Figure
5 and Table 1) and a write bit (R/ W = 0). Once the
slave address is recognized and the write bit is
received, the MAX11008 (I 2 C slave) issues an ACK by
pulling SDA low for one clock cycle. The master then
sends the register address byte (command byte) to the
MASTER TO SLAVE
SLAVE TO MASTER
slave. The MSB of the register address byte is the
read/write bit for the destination register address of the
slave and must be set to 0 for a write cycle (see the
Register Address Map section). After receiving the
byte, the slave issues another acknowledge, pulling
SDA low for one clock cycle. The master then writes
two data bytes, receiving an ACK from the slave after
each byte is sent. The master ends the write cycle by
issuing a STOP condition. When operating in HS mode,
a STOP condition returns the bus into F/S mode (see
the HS I 2 C Mode section). Figure 10 shows a complete
write cycle.
F/S MODE
HS MODE
F/S MODE
S
MASTER CODE
N
Sr
SLAVE ADDRESS
R/W
A
DATA
A
P
Figure 9. Data-Transfer Format in HS Mode
MASTER TO SLAVE
SLAVE TO MASTER
4-BYTE WRITE CYCLE
N BYTES + ACK
Sr
HS MODE CONTINUES
SLAVE ADD
1
7
1 1
8
1
8
1
8
1
1
NUMBER OF BITS
S
SLAVE
ADDRESS
W A
REGISTER ADDRESS
BYTE
A
DATA BYTE
A
DATA BYTE
A P OR Sr
MSB DETERMINES
WHETHER TO READ OR WRITE TO
REGISTERS
Figure 10. Write Cycle
22
______________________________________________________________________________________
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX11014BGTM+T
IC RF MESFET AMP 48-TQFN-EP
MAX12000ETB+T
IC AMP GPS FRONT 1575MHZ 10TDFN
MAX12005ETM+T
IC SATELLITE IF SWITCH 48-TQFN
MAX1385BUTM+
IC RF LDMOS BIAS CNTRLR 48-TQFN
MAX1470EUI+T
IC RECEIVER 315MHZ 28-TSSOP
MAX1470EVKIT-315
EVAL KIT FOR MAX1470 315MHZ
MAX1471EVKIT-315
EVAL KIT FOR MAX1471 315MHZ
MAX1472EVKIT-433#
EVAL KIT MAX1472
相关代理商/技术参数
MAX11008EVKIT+
功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V
MAX1100CWG
制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX1101
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Chip, 8-Bit CCD Digitizer with Clamp and 6-Bit PGA
MAX11014
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014_08
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014BGTM
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014BGTM+
功能描述:特殊用途放大器 Auto RF MESFET Amp Drain-Current Cntrlr RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel
MAX11014BGTM+T
功能描述:射频放大器 Auto RF MESFET Amp Drain-Current Cntrlr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel
